Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
We've discovered this great article pertaining to How to Install a Bathtub listed below on the web and felt it made sense to write about it with you here.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is easily easily accessible, the project can move speedily; if you need to open up a wall to remove the old tub and also place the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about using one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have currently purchased a brand-new bathtub and do not need to change the setup of your previous supply of water pipelines.
Your tools and product checklist need to make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water and also inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the tub has been made use of at the very least once as this will settle it right into its final position.
Getting ready for the Installation
To start with, the supporting structure provided with the bath must be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, triggering the water to pass through the wall in between the bathroom and the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very inquisitive about Tools You Need to Install a New Bathtub and I'm hoping you appreciated our post. Sharing is good. Helping people is fun. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Service Now
Report this page